Siding Materials

Siding

Detail	Amount	Additional Information
		https://www.maibec.com/imports/medias/pdf/en/siding/maibec-technical-sheet-modern.pdf Installation System: Maibec em+® Finish: Textured Actual Dimensions: 5/8” x 5 1/4" Exposed Surface: 4 9/16" Overlap: 11/16" Color: Coastal Charcoal 058
Touch Up Paint		Coastal Charcoal 058 Touch up paint
Starter Strips		https://www.maibec.com/imports/medias/pdf/en/metal-mouldings/maibec-technical-sheet-metal-starter-trim.pdf 14'+32'+20'+3' = 69' + 10% = 76'
Trim		https://www.maibec.com/imports/medias/pdf/en/regular-mouldings/maibec-technical-sheet-2-moulding-inside-or-outside-corner.pdf
Modern Casing (Can probably just use trim)		https://www.maibec.com/imports/medias/pdf/en/architectural-mouldings/maibec-technical-sheet-modern-casing-510-511.pdf
Stapler Guide
Stained maibec nails
Staples		Features Pneumatic Fasteners Used for em+ and URBAHN 2" Stainless Steel 7/16"  crown 16 gauge

Other Material Needed

Job Details

Square Footage

Kitchen Wall

• 14' x 12' = 168 sq feet
• Total Trim = 14' + 14' + 12' = 40'
• Furring Strips
• = 14'*12/16 + 3 x 12' = 162'

Back Wall

• 32' x 10.5' - 84 sq' (doors) = 336 - 84 = 252 sq'

• window 52x42.  total trim = 188" = 16'
• back door 81x75. total trim = 225" = 19'
• garage door 81x75. total trim = 225" = 19'
• edge pieces = 32' (top) + 22' edges = 54'
• Total trim: 108'

• Furring Strips
• = 32'*12/16 + 3 x 12' = 324'

Garage Wall

• Siding
• = 20' x 13' = 260 sq'

• Trim
• = 13' + 13' + 20' = 46'

• Furring Strips
• = 20'x12/16 +2  *13 = 221' 

Garage Front

• 11' x 13' - 64 sq' (door) = 143 - 64 = 70 sq'

• Trim
• = Garage Door 8'  + 8' + 8' = 24'
• + Edging= 13' + 13' + 11' = 37'
• = 61'

• Furring Strips
•  = (4' * 12/16 +2 )'*13' + 9' x 5' * 12/16
• = 65 + 34
• = 99'

Total:

Siding

• = 168 + 252 + 260 + 70
• = 750 sq' + 10% = 850'

Trim

• = 40 + 108 + 46 + 61
• = 255' + 10% = 280'

Furring Strips

• = 162 + 324 + 221 + 99
• = 806 + 10% 
• = 886' /8'
• =110

Ventilated Starter Strips

• 14'+32'+20'+3'
• = 69' + 10% = 76'

Flashing

Deck Flashing

Concrete Basement Flashing

Above Window

Windo/Door Flashing

Below Window

Top of Wall

• No flashing required

Window Casing arrangement

• Siding up against window

Installation

• Install 1x3 kiln dried furring strips on the studs

• Install weather sealing around all windows and doors

• Install Metal flashing above windows and where water drainage is needed.

• Install at least 8" above the ground

• Use metallic starter strip to ensure proper ventilation and prevent rodent and insect infestation 

• If you need to cut a board at 90 degrees, then you will need to apply touch up paint to the cut end

• If you have to make a joint cut, make a 45 degree cut at both ends and apply touch up paint.
• Attach at the furring strip.

• Use recommended staples and nails only and use the maibec stapler guide if possible.

• Used stained maibec nails where tongue and groove system removed.

• A common way to finish the wall is to add a molding and butt up the siding to it leaving a 1/2" spacing between the molding and the soffit.

• Caulking

References