Prerequisites

• Ubuntu 16 running in VirtualBox

VirtualBox

...

Preferences

In VirtualBox Preferences define Host-only adaptor (should already exist and default to the following)

• Ip: 192.168.56.1
• Netmask: 255.255.255.0
• DHCP: Enabled

Create K8Master Node

Create VM

Create a VM with the following:

• 2 GB MEM
• 10 GB disk
• user: test

Install SSH

For Networking assign the following:

Adaptor 1: NATNet

Adaptor 2: Host-only adapter (vboxnet0)

For Audio: Disable

Start VM and install Ubuntu Server 16

Networking Setup

Log into the VM and issue the following commands.> sudo apt-get install openssh-server

Determine your network interfaceinterfaces

> ifconfig -a

enp0s3    Link encap:Ethernet  HWaddr 08:00:27:ff:1a:7b  
          inet addr:19210.1680.562.315  Bcast:19210.1680.562.255  Mask:255.255.255.0
...

enp0s8    Link encap:Ethernet  HWaddr   inet6 addr: fe80::a00:27ff:feff:1a7b/64 Scope:Link08:00:27:eb:d0:60  
          UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
          RX packets:1680 errors:0 dropped:0 overruns:0 frame:0
          TX packets:2440 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1000 
          RX bytes:1446319723 (1419.47 KB)  TX bytes:219190 (210.90 KBB)

lo        Link encap:Local Loopback  
          inet addr:127.0.0.1  Mask:255.0.0.0
          inet6 addr: ::1/128 Scope:Host
          UP LOOPBACK RUNNING  MTU:65536  Metric:1
          RX packets:160 errors:0 dropped:0 overruns:0 frame:0
          TX packets:160 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1 
          RX bytes:11840 (11.8 KB)  TX bytes:11840 (11.8 KB)
...

From the above we can see that our vm is running with IP: 192.168.56.3has 2 network interfaces but only one is configured. The first interface is using NAT and has been assigned an IP address. We will need to add the second interface which is using the host-only network.

We are going to set this second interface (host-only) to a specific IP address: (Let's make it a static and assign it 192.168.56.100)

We might as well change the first interface to a static one too.

> sudo vi /etc/network/interfaces

# This file describes the network interfaces available on your system
# and how to activate them. For more information, see interfaces(5).


source /etc/network/interfaces.d/*

# The loopback network interface
auto lo
iface lo inet loopback

# The primary network interface
auto enp0s3
#iface enp0s3 inet dhcp
iface enp0s3 inet static
        address 19210.1680.562.100
        netmask 255.255.255.0
        network 19210.1680.562.0
        broadcast 19210.1680.562.255
        gateway 19210.1680.562.1
        dns-nameservers 19210.1680.562.1 8.8.8.8

auto enp0s8
iface enp0s8 inet static
        address 192.168.56.100
        netmask 255.255.255.0
        network 192.168.56.0
        broadcast 192.168.56.255

> reboot

After reboot, we should be able to confirm that the ip address is static by issuing the ifconfig command once more.

...

> ssh test@192.168.56.100

From the VM, confirm that you can resolve DNS by issuing the following command:

> nslookup google.com

We can also setup port forwarding via our NAT network to access our VM using

> ssh -p PORT test@localhost

Appendix - Virtual Box

Network Configurations

+-----------+-------------+-------------+----------------+----------------+
|           | VM <-> Host | VM1 <-> VM2 | VM -> Internet | VM <- Internet |
+-----------+-------------+-------------+----------------+----------------+
| HostOnly  |     Yes     |     Yes     |      No        |       No       |
| Internal  |     No      |     Yes     |      No        |       No       |
| Bridged   |     Yes     |     Yes     |      Yes       |       Yes      |
| NAT       |     No      |     No      |      Yes       |  Port forward  |
| NATNet    |     No      |     Yes     |      Yes       |  Port forward  |
+-----------+-------------+-------------+----------------+----------------+

Reference