You are viewing an old version of this page. View the current version.

Compare with Current View Page History

« Previous Version 55 Next »

 


Specifications

SpecificationDetails
MakeMaytag Bravos XL
ModelMVWB950YG0


Pictures


Repairs

Replacing the Bearings

The replacement of the bearings can be a complicated task but reviewing the following videos will help.

Parts

PartDescriptionImage
Bearing Kit

W10447783 Washer Tub Bearing Installation Tool & W10435302 Tub Seal and Bearing Kit Replacement for Maytag MVWB750YW0 Washing Machine - Compatible with W10447783 Tool Kit & W10435302 Bearing Kit


Will this bearing kit work for a MVWB950YGO?

Debbie Cfor Model NumberMVWB950YGO

ANSWERDebbie, Yes the bearing kitW10435302will work for your model washer. You will also need the bearing tool which is part numberW10447783

Answered by AppliancePartsPros.com   |   Thursday, November 19, 2015

https://www.appliancepartspros.com/answers-for-whirlpool-bearing-w10435302-ap5325033-question-180369.html


Steps

StepURL

https://www.youtube.com/watch?v=tmEShMg2WSY

Open Bravos Cover

Remove the top 2 screws at the back of the washer. Slide the top forward and lift.

https://www.youtube.com/watch?v=BU0MGgGj1-s

Main Repair Video

Some difference. Model is slightly different. Agitator is different, see next step. 

https://www.youtube.com/watch?v=6EPoTFUaAWI

Removing the tub if stuck

I had to do this. Just keep jacking until it comes out. 

https://www.youtube.com/watch?v=m7rfpFhIcX0

Pictures

Bearings Again!

So less than 2 years later, I am re-doing the bearings. Hopefully this time we have better luck. 

Process Changes:

  • Added a lot of glue and let it cure overnight before finishing assembly.


Notes:

  • When adding the top tub mounts as depicted in the picture, they should seat up tightly against the tub. You may have to pull the tub up or tighten the screws a little bit each to bring the tup up.



  • When attaching the agitator, I discovered that the top screw doesn't press hard enough against the shaft. This would cause the agitator to make a big GRRRR sound when spinning down.
  • Turns out the washer has become compressed. Added a couple of steel washers above the rubber washer to make a better fit.
  • Rubber washer dimensions seem to be roughly:
    • Thickness: 9mm
    • OD: 20mm
    • ID: 10-11mm

  • Should have replaced the washer hub but didn't. It still can slip a bit.


LF (Long Fill) Error Code

LF flashes when the water level does not change for a period of time OR water is present but control does not detect the water level changing.

  • Is water supply connected and turned on?
  • Are hose screens plugged?
  • Is water siphoning out of the drain hose? Check for proper drainhose installation.
  • Is the pressure hose connection from the tub to the machine/motor control pinched, kinked, plugged, or leaking air?



Replacing the Inlet Valve

https://www.youtube.com/watch?v=yje3SS9fIbE&t=6s


Old Valve


The red relay wires were not long enough so I had to extend them.


After replacing the valve, I noticed that the water through the detergent valve ran much faster. Must have been the issue.


Testing the resistance of the valves showed about 1.3kΩ.



PartDescriptionPictureURL
W10853723

Whirlpool Washer Water Inlet Valve


https://www.reliableparts.ca/product/inv_14902897

Buy on Amazon


Diagnostic Mode

To enter diagnostic mode:

  • turn washer off
  • pressing any button for three seconds, release three seconds (and repeat).

  • If successful, all of the LEDs will illuminate and the time will read 8:8'8.

  • Press the button again within 5 seconds to enter manual diagnostic mode.
  • If done successfully, a single beep occurs and the three-digit display shows the User Interface ID# (H 80, H 8 1, etc.) for 3 seconds, then displays 000 and the Add A Garment indicator LED flashes.


Manual Tests

To check FRESH valve select and press the following:

WHITES START/PAUSE (turns on Fresh valve, cycle indicator flashes) WASH TEMP (selecting hot = hot valve; warm = hot & cold valves; cold = cold valve) START/PAUSE (turns off Fresh valve, cycle indicator is steady on).


To check DETERGENT valve select or press the following:

SUPER WASH or HEAVY DUTY START/PAUSE (turns on Detergent valve, cycle indicator flashes) WASH TEMP (selecting hot = hot valve; warm = hot & cold valves; cold = cold valve) START/ PAUSE (turns off Detergent valve, cycle indicator is steady on).


To check FABRIC SOFTENER valve select or press the following:

NORMAL START/PAUSE (turns on Fabric Softener valve, cycle indicator flashes) WASH TEMP (selecting hot = hot valve; warm = hot & cold valves; cold = cold valve) START/PAUSE (turns off Fabric Softener valve, cycle indicator is steady on).


To check BLEACH valve select or press the following:

DELICATE/HANDWASH START/PAUSE (turns on Bleach valve, cycle indicator flashes) WASH TEMP (selecting hot = hot valve; warm = hot & cold valves; cold = cold valve) START/PAUSE (turns off Bleach valve, cycle indicator is steady on).


To Lock the Lid press the following:

WATER SAVE/SPRAY RINSE or REMINDER RESET. Repeat to unlock.


To Test the Motor press the following: (Lid needs to be Locked)

Spin: To activate Spin, lid must be closed with lid lock

SPIN SPEED Motor/basket spins at 23 rpm.

Repeat → Motor/basket spins at 530 rpm.

Repeat →  Motor/basket spins at 1000 rpm.

Repeat →  Motor turns off.


Parts

https://www.reliableparts.ca/lookup/215461


References

ReferenceURL
User Manual

Serice Manual

Partshttps://www.reliableparts.ca/lookup/215461/1463423
Drain Hose Installationhttps://www.youtube.com/watch?v=BW-EwI5NLBM
Installation Guide
*** Enter Diagnostic Modehttps://www.youtube.com/watch?v=v4vcQ8QNkXg&t=62s
Whirlpool Washer Repair - How to Replace the Valve (Whirlpool # W10853723)https://www.youtube.com/watch?v=bM2bXqE9H6s&t=396s
Maytag Washer LF Low Flow Fault Diagnose & Repairhttps://www.youtube.com/watch?v=N-iul4E3cTI&t=473s





  • No labels