...
- Added a lot of glue and let it cure overnight before finishing assembly.
Notes:
- When adding the top tub mounts as depicted in the picture, they should seat up tightly against the tub. You may have to pull the tub up or tighten the screws a little bit each to bring the tup up.
- When attaching the agitator, I discovered that the top screw doesn't press hard enough against the shaft. This would cause the agitator to make a big GRRRR sound when spinning down.
- Turns out the washer has become compressed.
- Thickness: 7mm
- Printed a washer using TPU with a thickness of 10mm and it still slips...
- Rubber washer dimensions should to be roughly:
- Thickness: 10mm
- OD: 20 mm
- ID: 10.5 mm
- Rubber washer dimensions should to be roughly:
- Added a stainless steel washer above the rubber washer to make a better fit.
- Could have replaced the washer hub but didn't. It still can slip a bit.
LF (Long Fill) Error Code
...
- Press the button again within 5 seconds to enter manual diagnostic mode.
If done successfully, a single beep occurs and the three-digit display shows the User Interface ID# (H 80, H 8 1, etc.) for 3 seconds, then displays 000 and the Add A Garment indicator LED flashes.
Manual Tests
To check FRESH valve select and press the following:
WHITES START/PAUSE (turns on Fresh valve, cycle indicator flashes) WASH TEMP (selecting hot = hot valve; warm = hot & cold valves; cold = cold valve) START/PAUSE (turns off Fresh valve, cycle indicator is steady on).
To check DETERGENT valve select or press the following:
SUPER WASH or HEAVY DUTY START/PAUSE (turns on Detergent valve, cycle indicator flashes) WASH TEMP (selecting hot = hot valve; warm = hot & cold valves; cold = cold valve) START/ PAUSE (turns off Detergent valve, cycle indicator is steady on).
To check FABRIC SOFTENER valve select or press the following:
NORMAL START/PAUSE (turns on Fabric Softener valve, cycle indicator flashes) WASH TEMP (selecting hot = hot valve; warm = hot & cold valves; cold = cold valve) START/PAUSE (turns off Fabric Softener valve, cycle indicator is steady on).
To check BLEACH valve select or press the following:
DELICATE/HANDWASH START/PAUSE (turns on Bleach valve, cycle indicator flashes) WASH TEMP (selecting hot = hot valve; warm = hot & cold valves; cold = cold valve) START/PAUSE (turns off Bleach valve, cycle indicator is steady on).
To Lock the Lid press the following:
WATER SAVE/SPRAY RINSE or REMINDER RESET. Repeat to unlock.
To Test the Motor press the following: (Lid needs to be Locked)
Spin: To activate Spin, lid must be closed with lid lock
SPIN SPEED Motor/basket spins at 23 rpm.
Repeat → Motor/basket spins at 530 rpm.
Repeat → Motor/basket spins at 1000 rpm.
Repeat → Motor turns off.
Parts
https://www.reliableparts.ca/lookup/215461
References
Reference | URL |
---|---|
User Manual | |
Serice Manual | |
Parts | https://www.reliableparts.ca/lookup/215461/1463423 |
Drain Hose Installation | https://www.youtube.com/watch?v=BW-EwI5NLBM |
Installation Guide | |
*** Enter Diagnostic Mode | https://www.youtube.com/watch?v=v4vcQ8QNkXg&t=62s |
Whirlpool Washer Repair - How to Replace the Valve (Whirlpool # W10853723) | https://www.youtube.com/watch?v=bM2bXqE9H6s&t=396s |
Maytag Washer LF Low Flow Fault Diagnose & Repair | https://www.youtube.com/watch?v=N-iul4E3cTI&t=473s |
...